Wavenode SWR and RF wattmeter with computer graphics and DC power monitoring. Complete with SWR protection and high power remote sensor. Also includes audio and voice announcement of RF power and SWR.

Introducing WaveNode WN-2d to our family of products

Click here for our technical presentation.

WaveNode puts your station PC to work

WaveNode WN-2(d):

	WN-2d includes high brightness LED bargraphs.
	Monitor 4 sensors simultaneously for peak, Average power and coax SWR.
	Direct USB full speed interface.
	Backlit LCD display for stand-alone operation- Your PC is optional.
	Oscilloscope and Spectrum Analysis of the RF Modulation- Observe IM and "Splatter" frequency components realtime.
	Complete system includes (1) sensor, WN-2(d) unit, AC power module and software on CDROM.
	Wide range of sensors cover 100 milliwatt to 8KW, 1.6 Mhz to 1.3 Ghz.
	16-bit RISC processor, 12 bit A/D converter and rugged construction.
	WN-2(d) are compact and low power. Perfect for local, mobile, emergency communications vans, and remote repeater sites.
	NIST traceable calibration, FCC Class B, CE certification.

New for 2010

RF Sensors for coupling to RF measurement equipment and phased array antenna adjustment.

CS-1

Frequency range: 1.8Mhz - 60Mhz

Output voltage: 1Volt RMS at 100 watts

Output impedance: 50 ohms

Range: 0 -2000 watts continuous

WaveNode Announces Three New Sensors for 470 MHz to 1.3 GHz.

These sensors are for 0-100 watt operation and are compatible with WN1 and WN2 systems. They have low insertion loss and are built on PTFE stripline with dual differential detectors. True peak and average power with SWR are displayed on your system, and includes a 50 ohm BNC port for monitoring modulation waveforms.

SHF-1 470 MHz - 750 MHz

SHF-2 750 MHz - 950 MHz

SHF-3 950 MHz - 1.3 GHz

These units have >23 db directivity and will display SWR accurately at power levels > 2 watts.

Now Available...

High Power HF and QRP Sensors!

8KW HF Sensor

WaveNode now has available an HF sensor up to 8KW operation. Same price as our standard 2KW sensor -- $60.00 each. Choose either SO-239 (Silver-Teflon-Gold) or "N" type connector.

This sensor is suitable for use with linear amplifiers capable of > 2KW watts PEP output. Plug compatible with our other sensors to give maximum flexibility to your measurement capability, you can mix and match these sensors with our HF and UHF sensors to provide multiple RF power measurement on a single display!

QRP HF Sensor

The QRP HF sensor extends our sensor lineup to satisfy the needs of the QRP operator. Same price as our 2KW and 8KW -- $60.00 each.

This sensor provides accurate Power and SWR measurement between 20 milliwatts and 60 watts. Mix and match with our other sensors to provide QRP to QRO measurement, no compromise. The WaveNode Sensor selection now provides 0.025--8KW measurement from 1.6-1.3 GHz, all on a single display!

WaveNode WN-2 at the FCC test range

NIST traceable calibration station

FM-1 Sensor for FM Broadcast and EmComm: Perfect for local or remote Monitoring of Police/Fire/FM Broadcast. Handles 0-600 Watt forward power with < .03 db insertion loss. Monitor transmitter power and antenna/feedline SWR remotely. Available with RFView and your choice of RF connector.

WN2 Version 2.4 now available with TuneTone and hardcopy 24 hr logging utility and additional rotator views. Click Here

It's Here!!!

RT1/RT2 controller for Yaesu© rotators.

The newest Hardware accessory for the WN2(d) station monitor.

	Available as option on new units.
	Easy field installation of module RT1/RT2 on existing units.
	All software versions support RT1/RT2.

The Rotator Controller:

Features of your RT-1/ RT-2 Rotor Control System:

1. Point and click control on a map centered at your location.
Just one click sends your rotator exactly where you want it.

2. Controls 2 independent rotators, and indicates both rotators
on the same map. Two auxiliary antennas at 90 degrees can
also be indicated.

3. No alignments are necessary, but provision is made to trim
the antenna pointing.

4. Supports Overlap, speed control, and all Yaesu© features.
Use your rotator box controls normally also. Uses the Yaesu©
interface plug, no opening or modification of your Rotator
Conrol Unit.

5. Simple connection to your control box that will never lose
communication with your WN-1 or with your Yaesu© control box.
Perfect for remote operation where reliability is most important.
There are no communication protocols, data rates, irq’s, or
addresses to set. It just works!

High-Power UHF Enthusiasts!

Wavenode now offers 3 new 2 KW Sensors:

120-170 MHz.

200-270 MHz.

410-470 Mhz.

These sensors use a unique "COAX Directional Coupler" to display Power
and SWR with very low insertion loss. Insertion loss is less than 2 watts
with 1.5KW forward power.

Accuracy +/- 10%

Directivity >25db

Connectiors SO-239 or "N" Type

RFView

Monitor your output like the pros!

HF-1 sensor shown with RFView option

Optional RFView output port on WaveNode HF sensor allows the
operator to view station signals on an oscilloscope.

Plug a BNC cable from the remote sensor to your oscilloscope for
realtime RF monitoring.

WaveNode Online Store

Now you can complete your credit card order online in
our secure store.

Tools for RF Power Measurement and Realtime RF Analysis